surface mount high efficiency rectifier voltage range 50 to 600 volts current 0.5 ampere rectron semiconductor technical specification features * low power loss, high efficiency * low leakage * low forward voltage * high current capability * high speed switching * high surge capability * high reliability mechanical data * epoxy: device has ul flammability classification 94v-o * mounting position: any * weight: 0.016 gram maximum ratings and electrical characteristics ratings at 25 o c ambient temperature unless otherwise specified. single phase, half wave, 60 hz, resistive or inductive load. for capacitive load, derate current by 20%. electrical characteristics (at t a = 25 o c unless otherwise noted) 05H1L thru 05h6l sod-123fl maximum ratings (at t a = 25 o c unless otherwise noted) notes : 1. test conditions: i f = 0.5a, i r = -1.0a, i rr = -0.25a 2. measured at 1 mh z and applied reverse voltage of 4.0 volts dimensions in inches and (millimeters) 2006-3 rev:o ratings maximum recurrent peak reverse voltage maximum rms voltage maximum dc blocking voltage maximum average forward rectified current at t a = 55 o c peak forward surge current 8.3 ms single half sine-wave superimposed on rated load (jedec method) typical junction capacitance (note 2) operating and storage temperature range symbol v rrm v dc i o i fsm c j t j , t stg v rms amps 0.5 15 15 -55 to + 150 amps pf 0 c units 50 35 50 100 70 100 volts volts volts 12 200 140 200 600 420 600 50 at rated dc blocking voltage t a = 25 o c characteristics maximum full load reverse current average, full cycle .375? (9.5mm) lead length at t l = 55 o c maximum reverse recovery time (note 1) v f symbol i r trr 5.0 100 75 uamps uamps nsec maximum dc reverse current maximum instantaneous forward voltage at 0.5a dc volts units 1.0 1.7 1.3 400 280 400 300 210 300 05H1L 05h2l 05h3l 05h4l 05h5l 05h6l 05H1L 05h2l 05h3l 05h4l 05h5l 05h6l 3. ?fully rohs compliant?, ?100% sn plating (pb-free)?. .150 (3.8) .142 (3.6) . 035 (0.90) . 028 (0.70) .039 (1.00 ) .035 (0.9 0) .077 (1.95 ) .069 (1.75 ) .030 (0.75) .022 (0.55) . 008 (0.20) .114 (2.9) .106 (2.7)
rectron rating and characteristic curves ( 05H1L thru 05h6l ) fig. 6 - typical junction capacitance junction capacitance, (pf) reverse voltage, ( v ) 200 100 60 40 20 10 6 4 2 1 .1 .2 .4 1.0 2 4 10 20 40 100 05H1L~05h5l 05h6l t j = 25 fig. 1 - test circuit diagram and reverse recovery time characteristic 50 noninductive 10 noninductive d.u.t 25 vdc (approx) ( - ) ( - ) ( + ) ( + ) 1 non- inductive oscilloscope (note 1) pulse generator (note 2) notes: 1 rise time = 7ns max. input impedance = 1 megohm. 22pf. 2. rise time = 10ns max. source impedance = 50 ohms. trr +0.5a 0 -0.25a -1.0a 1cm set time base for 10/20 ns/cm fig. 2 - typical forward current derating curve average forward curent, (a) ambient temperature ( ) 1.0 0.5 0 25 50 75 100 125 150 175 0 single phase half wave 60hz resistive or inductive load fig. 4 - typical instantaneous forward instantaneous forward current, (a) instantaneous forward voltage, (v) 10 1.0 .1 .01 .001 0 .2 .4 .6 .8 1.0 1.2 1.4 1.6 1.8 pulse width = 300us 1% duty cycle t j = 25 600v 50/100/200v 300/400v fig. 3 - typical reverse characteristics instantaneous reverse current, (ua) percent of rated peak reverse voltage, (%) t j = 25 t j = 100 t j = 150 100 10 1.0 .1 .01 40 0 20 60 80 100 120 140 fig. 5 - maximum non-repetitive forward surge current peak forward surge current, (a) number of cycles at 60hz 21 18 15 12 9 6 3 0 1 2 5 10 20 50 100 8.3ms single half sine-wave ( jedec method ) characteristics
mounting pad layout rectron dimensions in inches and (millimeters) 0.029 min . (0.73 min .) 0.150 0.014 min. (0.36 min.) (3.80) ref
|
